Guides

Asphalt Driveway Permit in Hickory, NC

Stoutwell Paving · September 30, 2026 · 6 min read

Freshly sealed asphalt driveway in front of a ranch house with a two-car garage

The City of Hickory’s Engineering page says its staff can answer questions on “issuance of driveway permits”, next to street paving petitions and curb and gutter petitions. That is the office to ask about a driveway on a City street. For the paving itself, see the Hickory asphalt driveway paving page; below is what the City prints.

Two City pages are used. One is the Engineering page, which carries no date. The other is the 400 series of the Engineering Department Manual of Practice, titled “400 Curb & Gutter, Sidewalks & Driveways”, where every standard prints its own date in its title block. Below is what the pages say about driveways; for the application and inspection steps, ask the Engineering Division.

Which City office handles driveway permits in Hickory

The Engineering page describes what its staff can help with: “professional engineering and surveying for municipal projects, storm water, transportation planning, street paving petitions, curb and gutter petitions, sidewalk petitions, official City maps, thoroughfare maps, verification of addresses, and issuance of driveway permits.” The driveway standards live in the same department’s Manual of Practice, in Division 400. The first question below has a short answer from that page: driveway permit issuance is a subject its Engineering staff answer questions on, and the driveway standards are Engineering Department documents.

What the Typical Driveway Cut drawing shows for a home

Standard 402, titled TYPICAL DRIVEWAY CUT and dated 2-1-07, is a plan view of a driveway meeting a curb and gutter. One arrowed span runs across the top of the driveway and carries two labels, “RESIDENTIAL: 15’-24’” and “COMMERCIAL: 20’*-36’”, with a footnote reading “COMMERCIAL: TWO-WAY MINIMUM 20’”. A separate arrow near the property line carries the label “3’ MIN”.

The drawing also labels 3’R at each curved corner, 6” at several points, 3.5’ and 2’ along vertical dimension lines, and it is marked NOT TO SCALE. What each of those dimensions measures is not spelled out in words on the sheet, so the Engineering Division is the office to confirm them.

The word typical matters. Note 5 on the general notes sheet, covered next, leaves the final width to the City Engineer or their appointee.

The City Engineer’s say over new and altered driveways

Standard 401, the general notes for the 400 series, is dated 06-22-26. Two of its notes give the City Engineer authority over where and how a driveway goes in.

Note 5 reads: “The final design, location, width, and number of new and altered driveways shall be up to the discretion of the City Engineer or their appointee.” The sheet does not say where a repair or an overlay stops and an altered driveway begins. Resurfacing and rebuilding are compared in the asphalt overlay vs replacement guide; whether a planned job counts as altering a driveway is a question for the Engineering Division.

Note 3 covers intersections: “No driveway shall be installed within thirty (30) feet of an intersection, measuring from the point of tangency, without express written approval by City Traffic Engineer and/or City Engineer.” That is the basis for the third question below.

Standard 402 adds one note of its own. Here it is exactly as printed:

ALL DRIVEWAY LOCATIONS, GRADES, AND CUTS SHALL BE AT A MINIMUM IN ACCORDANCE WITH THE LATEST EDITION OF THE “POLICY ON STREET AND DRIVEWAY ACCESS TO NORTH CAROLINA HIGHWAYS,” PUBLISHED BY THE NORTH CAROLINA DEPARTMENT OF TRANSPORTATION TRAFFIC ENGINEERING BRANCH.

Where the sidewalk and a concrete turnout meet an asphalt driveway

Standard 404, DRIVEWAY TURNOUT RADIUS TYPE, is dated 2-1-07 and runs to two sheets. Its first sheet is a plan of a paved driveway turnout showing the sidewalk, the curb, the gutter and grass areas on each side. One hatched area carries the label “THIS AREA TO BE PAVED WITH CONCRETE PAVEMENT”. Other labels on the sheet read “TERMINUS POINT FOR PROPOSED DRIVEWAY” and “AT LOCATIONS AS DIRECTED BY THE ENGINEER”.

So the City’s own drawing shows a concrete section where a driveway meets the curb and sidewalk. What pavement the City accepts on the rest of a particular driveway is a question for the Engineer under note 5. General differences between the two surfaces are in the asphalt vs concrete driveway guide.

Sidewalks matter here too. Note 1 of Standard 401 sets sidewalk concrete at four inches thick, “except where a sidewalk crosses a driveway it shall be six (6) inches thick”.

The second sheet of the turnout drawing shows a “METHOD OF TIE IN”. Its note reads: “WHEN EXISTING DRIVEWAY PAVEMENT IS CONCRETE, A SAW CUT 2” DEEP SHALL BE REQUIRED AT THE POINT OF TIE IN WITH EXISTING DRIVEWAY GRADE.” The condition in that sentence is existing concrete; how it applies to a given address is for the City’s Engineer to confirm.

Addresses outside the City of Hickory

The manual and the Engineering page quoted here are City of Hickory documents. Newton, Conover, Morganton, Lenoir and every other city, town and county follow their own rules, so a driveway in one of them goes to that government’s own office.

Three checks for a Hickory driveway before paving

The right driveway depends on the soil and base, the drainage, local permit rules and the weather when the asphalt goes down. Requirements vary by site, scope and jurisdiction; the city or county permit office and an on-site inspection determine what applies.

Each check below ties back to a City sheet quoted above:

  • Is the lot inside the City of Hickory, whose Engineering Department Manual of Practice is quoted here?
  • Would the driveway sit within thirty feet of an intersection, or touch the curb, the gutter or a sidewalk?
  • Is any part of the job new, altered or a join to an existing concrete apron, and who at the City confirms it?

Frequently Asked Questions

Who issues a driveway permit inside the City of Hickory?

The City’s Engineering Division: its page lists issuance of driveway permits among the subjects staff answer questions on, and the driveway standards sit in the Engineering Department’s Manual of Practice.

How wide can a residential driveway cut be on a Hickory City street?

Standard 402 prints RESIDENTIAL: 15’-24’ on its Typical Driveway Cut drawing, and note 5 of Standard 401 leaves the final width to the City Engineer or their appointee.

Can a new driveway go near an intersection in Hickory?

Note 3 of Standard 401 says no driveway shall be installed within thirty (30) feet of an intersection, measured from the point of tangency, without express written approval by the City.

Is a driveway in Newton or Conover held to Hickory’s Manual of Practice?

These are the City of Hickory’s own standards. Newton, Conover, Morganton, Lenoir and every other city, town and county follow their own rules, so an address there goes to its own office.

Get a free quote across the Hickory metro

Stoutwell Paving serves Hickory, paving new driveways, replacing worn ones and laying overlays. Parking lot prices are on the Hickory pricing page, and the Hickory contact page takes an address for a free quote.

Ready for a Free Quote?

Get a free, no-obligation quote for property in the Hickory metro of North Carolina.

Get Your Free Quote

Or call us directly: (919) 219-2946

Final scope, schedule, and pricing are confirmed after an on-site inspection and documented in the written project agreement.

Get a free quote for your lot

We seal, stripe and repair lots for churches, schools and shopping centers.

Call Free Quote